Pagrindinis meniu

Transporto priemonė: TYP 180D BM 120.110-.111, .100-.102; VIN numerio dalis: 120102
Grupė: 07 INJECTION PUMP, MIXTURE CONTROLLER, SUCTION NOISE DAMPER, SUCTION PIPE AND EXHAUST MANIFOLD - 005 INJECTION PUMP
5796
# Kodas Pavadinimas
X XXXXXXXXXXXX PART NAME MISSING
INJECTION PUMP
A 0000749302 REPLACED BY
002 074 01 01 TOGETHER WITH 1 STOP ANGLE 636 074 02 40 UP TO ENGINE 5516035
A 0010745401 INJECTION PUMP
001 A 0020740101 INJECTION PUMP
FROM ENGINE 5516036
A 0010743401 PART NAME MISSING
A 0010747701 INJECTION PUMP
A 0020740201 INJECTION PUMP
A 6360740140 STOP ANGLE
FOR CHOKE AND STOPPER CABLE AT INJECTION PUMP UP TO ENGINE 5516035
002 A 6360740240 STOP ANGLE
FOR CHOKE AND STOPPER CABLE AT INJECTION PUMP FROM ENGINE 5516036
003 A 0000740315 PRESSURE VALVE
WITH VALVE SUPPORT
004 A 0000741693 COIL SPRING
FOR PRESSURE VALVE
A 0009972340 SEALING RING
FOR PIPE CONNECTIONS
005 SEALING RING
001 997 3040 FOR PIPE CONNECTIONS
006 A 0000780069 PIPE CONNECTION
FOR PRESSURE VALVES
A 0000780135 CLAMPING JAW WITH THREAD
TO CLAMP PIPE CONNECTIONS
007 A 0000780335 CLAMPING JAW WITH THREAD
TO CLAMP PIPE CONNECTIONS
008 A 0000780235 CLAMPING JAW
WITHOUT THREAD TO CLAMP PIPE CONNECTIONS
COUNTERSUNK SCREW
AM 6X22 DIN 63-4 S FOR CLAMPINGJAWS 000 078 01 35/00 35
CYLINDRICAL SCREW
BM 6X28 DIN 84-4 S FOR CLAMPINGJAWS 000 078 02 35/03 35
LOCK WASHER
B 6 DIN 127 FOR CLAMPINGJAWS 000 078 02 35/03 35
SEALING RING
A 6X10 DIN 7603 A1 FOR BREATHER SCREW
A 0000740171 BREATHER SCREW
ON INJECTION PUMP, FRONT SIDE
011 A 0000740671 BREATHER SCREW
ON INJECTION PUMP, FRONT SIDE
SEALING RING
A 10X14 DIN 7603 A1 FOR ANNULAR FITTING
ANNULAR FITTING
B 4 DIN 7622 FOR OIL OVERFLOW
HOLLOW SCREW
A 4 DIN 7623 TO FIX ANNULAR FITTING, FOR OIL OVERFLOW
A 0000741060 OIL DIPSTICK
017 A 0000741360 OIL DIPSTICK
018 A 0000750032 BREATHER FILTER
ON GOVERNOR
SEALING RING
A 12X16 DIN 7603CU
A 0000750207 DIAPHRAGM
FOR GOVERNOR
A 0000750307 DIAPHRAGM
FOR GOVERNOR
020 A 0000750407 DIAPHRAGM
FOR GOVERNOR
X XXXXXXXXXXXX PART NAME MISSING
FUEL PUMP
025 A 0000914101 FUEL PUMP
WITHOUT PRE-FILTER
026 A 0000910010 VALVE
SUCTION AND PRESSURE VALVE
027 A 0000910319 PRESSURE SPRING
FOR SUCTION AND PRESSURE VALVE
028 A 0009970730 SCREW PLUG
FOR PRESSURE VALVE
029 A 0000911101 HAND PUMP
FOR FUEL PUMP
SEALING RING
A 14X20 DIN 7603 A1 FOR HOLLOW SCREW
HOLLOW SCREW
A 8 DIN 7623 FOR FUEL LINE AT FUEL PUMP
035 A 0000910580 GASKET
BETWEEN FUEL PUMP AND INJECTION PUMP
WASHER
6,4 DIN 433 FOR FUEL PUMP AT INJECTION PUMP
LOCK WASHER
B 6 DIN 127 FOR FUEL PUMP AT INJECTION PUMP
HEX. NUT
M 6 DIN 934-5 S FOR FUEL PUMP AT INJECTION PUMP
039 A 0000742727 CONTROL LEVER
ON CONTROL SHAFT TO INJECTION PUMP
LOCK WASHER
B 5 DIN 127 FOR CONTROL LEVER ON CONTROL SHAFT
HEX.-HD.SCREW
M 5X15 DIN 933-8 G FOR CONTROL LEVER ON CONTROL SHAFT
WOODRUFF KEY
2X3,7 DIN 6888 FOR CONTROL LEVER ON CONTROL SHAFT
WASHER
5,3 DIN 433 OPTIONAL FOR CHOKE AND STOPPER CABLE AT CONTROL LEVER
SPRING WASHER
5 N 55 A OPTIONAL FOR CHOKE AND STOPPER CABLE AT CONTROL LEVER
COTTER PIN
1,5X12 DIN 94 FOR CHOKE AND STOPPER CABLE AT CONTROL LEVER
WOODRUFF KEY
3X5 DIN 6888
051 A 6360770309 FOLLOWER
FOR INJECTION PUMP
LOCK WASHER
B 12 DIN 127 FOR FOLLOWER AT INJECTION PUMP
HEX. NUT
M 12 DIN 934-5 S FOR FOLLOWER AT INJECTION PUMP
SEALING RING
A 12X16 DIN 7603 A1
THREADED NIPPLE
6 DIN 7627 FOR CONNECTION OF VACUUM LINE BETWEEN INJECTION PUMP GOVERNOR AND MIXTURE CONTROLLER UP TO ENGINE 8500349
056 A 6360740480 GASKET
BETWEEN TIMING GEAR CASE COVER AND INJECTION PUMP
WASHER
10,5 DIN 125 FOR INJECTION PUMP AT TIMING GEAR CASE COVER
HEX. NUT
M 10 DIN 934-5 S FOR INJECTION PUMP AT TIMING GEAR CASE COVER
GROOVED BEARING
16002 DIN 625 UP TO ENGINE 4500145
GROOVED BEARING
6202 DIN 625 FROM ENGINE 4500146
LOCKING RING
32X1,2 DIN 472 UP TO ENGINE 4500145
LOCKING RING
35X1,5 DIN 472 FROM ENGINE 4500146
A 6360770205 DRIVE SHAFT
FOR INJECTION PUMP UP TO ENGINE 4505074
A 6360770405 DRIVE SHAFT
FOR INJECTION PUMP FROM ENGINE 4505075-5514611
061 A 6360770505 DRIVE SHAFT
FOR INJECTION PUMP FROM ENGINE 5514612
A 6360770053 SPACER TUBE
BETWEEN GROOVED BEARINGS ON DRIVE SHAFT UP TO ENGINE 4500145
A 6360770253 SPACER TUBE
BETWEEN GROOVED BEARINGS ON DRIVE SHAFT FROM ENGINE 4500146-4505074
062 A 6360770153 SPACER TUBE
BETWEEN GROOVED BEARINGS ON DRIVE SHAFT FROM ENGINE 4505075
063 A 6360770152 ADJUSTING RING
FOR DRIVE SHAFT FROM ENGINE 4505075-5514611
WOODRUFF KEY
3X5 DIN 6888 FOR DRIVE GEAR, OR INJECTION TIMING GEAR RESP., AT DRIVE SHAFT
A 6360770212 DRIVE GEAR, 40 TEETH
FOR INJECTION PUMP UP TO ENGINE 5514611
065 A 6360700045 INJECTION TIMING GEAR
FROM ENGINE 5514612
066 A 6360750125 SEGMENT FLANGE
FROM ENGINE 5514612
067 A 6360750035 BALANCING WEIGHT
FROM ENGINE 5514612
068 A 6360750025 SEGMENT PLATE
FROM ENGINE 5514612
A 6360750174 PIN
FOR SPRING SEAT FROM ENGINE 5514612
069 A 6210750274 PIN
FOR SPRING SEAT FROM ENGINE 5514612
A 6369930301 PRESSURE SPRING
FROM ENGINE 5514612
070 A 6369930501 PRESSURE SPRING
FROM ENGINE 5514612
A 6360750074 PIN
FOR TIMING LIMIT FROM ENGINE 5514612
071 A 6210750174 PIN
FOR TIMING LIMIT FROM ENGINE 5514612
072 A 6360770612 DRIVE GEAR
FROM ENGINE 5514612
A 6360700054 PART NAME MISSING
FROM ENGINE 5514612
A 6360750050 BUSHING
FOR DRIVE GEAR FROM ENGINE 5514612
073 A 6360750350 BUSHING
FOR DRIVE GEAR FROM ENGINE 5514612
SPRING WASHER
B 8 DIN 137 FROM ENGINE 5514612
HEX.-HD.SCREW
M 8X12 DIN 933-8 G FROM ENGINE 5514612
076 A 6360750062 THRUST WASHER
FROM ENGINE 5514612
WASHER
13 DIN 125 FOR DRIVE GEAR, OR INJECTION TIMING GEAR RESP., AT DRIVE SHAFT
LOCK WASHER
B 12 DIN 127 FOR DRIVE GEAR, OR INJECTION TIMING GEAR RESP., AT DRIVE SHAFT
HEX. NUT
M 12X1,5 DIN 934-5 S FOR DRIVE GEAR, OR INJECTION TIMING GEAR RESP., AT DRIVE SHAFT
X XXXXXXXXXXXX PART NAME MISSING
UNIT PARTS FOR SUBSEQUENT INSTALLATION OF INJECTION TIMING GEAR
A 6360700099 UNIT PARTS
FOR SUBSEQUENT INSTALLATION OF INJECTION TIMING GEAR UP TO ENGINE 4500145 THE FOLLOWING PARTS MUST BE DELIVERED IN ADDIT
A 6360700045 INJECTION TIMING GEAR
UP TO ENGINE 4500145 THE FOLLOWING PARTS MUST BE DELIVERED IN ADDITION 1 TIMING GEAR CASE COVER 636 010 20 17 1 SPACER T
A 6360750062 THRUST WASHER
UP TO ENGINE 4500145 THE FOLLOWING PARTS MUST BE DELIVERED IN ADDITION 1 TIMING GEAR CASE COVER 636 010 20 17 1 SPACER T
A 6360770505 DRIVE SHAFT
UP TO ENGINE 4500145 THE FOLLOWING PARTS MUST BE DELIVERED IN ADDITION 1 TIMING GEAR CASE COVER 636 010 20 17 1 SPACER T
A 6360150530 COVER
UP TO ENGINE 4500145 THE FOLLOWING PARTS MUST BE DELIVERED IN ADDITION 1 TIMING GEAR CASE COVER 636 010 20 17 1 SPACER T
WASHER
13 DIN 125 UP TO ENGINE 4500145 THE FOLLOWING PARTS MUST BE DELIVERED IN ADDITION 1 TIMING GEAR CASE COVER 636 010 20 17
A 6360920420 SHIM
UP TO ENGINE 4500145 THE FOLLOWING PARTS MUST BE DELIVERED IN ADDITION 1 TIMING GEAR CASE COVER 636 010 20 17 1 SPACER T
HEX.-HD.SCREW
M 12X55 DIN 931-8 G UP TO ENGINE 4500145 THE FOLLOWING PARTS MUST BE DELIVERED IN ADDITION 1 TIMING GEAR CASE COVER 636
A 6360150271 FIXING SCREW
WITH TIMING NEEDLE UP TO ENGINE 4500145 THE FOLLOWING PARTS MUST BE DELIVERED IN ADDITION 1 TIMING GEAR CASE COVER 636 0
WITH THE
FOLLOWING INSTALLED PARTS TO BE REMOVED: DRIVE SHAFT 636 077 04 05 DRIVE GEAR 636 077 02 12 COVER 636 015 01 30 HEX.-HD.
A 6360770116 COUPLING SLEEVE
FOR INJECTION PUMP DRIVE UP TO ENGINE 4500145
080 A 6360770216 COUPLING SLEEVE
FOR INJECTION PUMP DRIVE FROM ENGINE 4500146
081 A 6369940135 SNAP RING
IN COUPLING SLEEVE
X XXXXXXXXXXXX PART NAME MISSING
NOZZLE HOLDER
082 A 0000172821 NOZZLE HOLDER
WITH INJECTION NOZZLE
A 0000173121 NOZZLE HOLDER BODY
A 0000170454 THROUGH FITTING
FOR CONNECTION OF LEAK OIL LINE
083 A 0000170654 THROUGH FITTING
FOR CONNECTION OF LEAK OIL LINE
084 A 0000170255 HEX. NUT
TO FIX THROUGH FITTING ON NOZZLE HOLDER BODY
A 0000172952 SHIM, 1.0 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
085 A 0000173652 SHIM, 1.0 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000173052 SHIM, 1.05 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000173752 SHIM, 1.05 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000171252 SHIM, 1.10 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000173852 SHIM, 1.10 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000171352 SHIM, 1.15 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000173952 SHIM, 1.15 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000171452 SHIM, 1.20 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000174052 SHIM, 1.20 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000171552 SHIM, 1.25 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000174152 SHIM, 1.25 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000171652 SHIM, 1.30 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000174252 SHIM, 1.30 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000171752 SHIM, 1.35 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000174352 SHIM, 1.35 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000171852 SHIM, 1.40 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000174452 SHIM, 1.40 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000171952 SHIM, 1.45 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000174552 SHIM, 1.45 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000172052 SHIM, 1.50 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000174652 SHIM, 1.50 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000172152 SHIM, 1.55 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000174752 SHIM, 1.55 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000172252 SHIM, 1.60 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000174852 SHIM, 1.60 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000172352 SHIM, 1.65 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000174952 SHIM, 1.65 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000172452 SHIM, 1.70 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000175052 SHIM, 1.70 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000172552 SHIM, 1.75 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000175152 SHIM, 1.75 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000172652 SHIM, 1.80 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000175252 SHIM, 1.80 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000175352 SHIM, 1.85 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000175452 SHIM, 1.90 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
A 0000175552 SHIM, 1.95 MM THICK
FOR ADJUSTMENT OF INJECTION PRESSURE
086 A 0000170417 PRESSURE SPRING
IN NOZZLE HOLDER
A 0000170174 THRUST BOLT
IN NOZZLE HOLDER
087 A 0000170274 THRUST BOLT
IN NOZZLE HOLDER
A 0000170022 NOZZLE HOLDER ELEMENT
088 A 0000170122 NOZZLE HOLDER ELEMENT
089 A 0000170516 BOX NUT
TO FIX INJECTION NOZZLE
SEALING RING
A 8X12 DIN 7603 A1 FOR HOLLOW SCREW FOR LEAK OIL LINE AT NOZZLES
HOLLOW SCREW
A 3 DIN 7623 FOR CONNECTION OF LEAK OIL LINE FOR LEAK OIL LINE AT NOZZLES
092 A 0000171312 INJECTION NOZZLE
IN NOZZLE HOLDER
A 0000171612 INJECTION NOZZLE
FOR ENGINES WITH AN ESPECIALLY STROG DIESEL KNOCK
A 3120170420 REPLACED BY
636 017 01 20 TOGETHER WITH 1 THREADED RING 636 017 03 03 UP TO ENGINE 5500957
093 A 6360170120 GASKET
BETWEEN NOZZLE HOLDER AND PRECHAMBER FROM ENGINE 5500958
X XXXXXXXXXXXX PART NAME MISSING
PRESSURE AND LEAK PIPE
100 A 6360703233 PRESSURE PIPE, BENT
FOR CYLINDER 1 FROM INJECTION PUMP TO NOZZLE HOLDER
101 A 6360703333 PRESSURE PIPE, BENT
FOR CYLINDER 2 FROM INJECTION PUMP TO NOZZLE HOLDER
A 6360703033 REPLACED BY
636 070 34 33 TOGETHER WITH 1 PRESSURE LINE 636 070 35 33 UP TO ENGINE 7516775
102 A 6360703433 PRESSURE PIPE, BENT
FOR CYLINDER 3 FROM INJECTION PUMP TO NOZZLE HOLDER FROM ENGINE 8516776
A 6360703133 REPLACED BY
636 070 35 33 TOGETHER WITH 1 PRESSURE LINE 636 070 34 33 UP TO ENGINE 8516775
103 A 6360703533 PRESSURE PIPE, BENT
FOR CYLINDER 4 FROM INJECTION PUMP TO NOZZLE HOLDER FROM ENGINE 8516776
104 A 6360780235 PIPE CLAMP
FOR PRESSURE LINES 1, 2, 3 AND 4 UP TO ENGINE 4507500
104 A 6360780235 PIPE CLAMP
FOR PRESSURE LINES 1, 2, 3 AND 4 FROM ENGINE 4507501-6501468
104 A 6360780235 PIPE CLAMP
FOR PRESSURE LINES 1, 2, 3 AND 4 FROM ENGINE 6501469
HEX. -HD. SCREW
M 5X12 DIN 933-8 G FOR PIPE CLAMP AT PRESSURE PIPE UP TO ENGINE 4507500
HEX. -HD. SCREW
M 5X12 DIN 933-8 G FOR PIPE CLAMP AT PRESSURE PIPE FROM ENGINE 4507501-6501468
HEX. -HD. SCREW
M 5X12 DIN 933-8 G FOR PIPE CLAMP AT PRESSURE PIPE FROM ENGINE 6501469
LOCK WASHER
B 5 DIN 127 FOR PIPE CLAMP AT PRESSURE PIPE UP TO ENGINE 4507500
LOCK WASHER
B 5 DIN 127 FOR PIPE CLAMP AT PRESSURE PIPE FROM ENGINE 4507501-6501468
LOCK WASHER
B 5 DIN 127 FOR PIPE CLAMP AT PRESSURE PIPE FROM ENGINE 6501469
HEX. NUT
M 5 DIN 934-5 S FOR PIPE CLAMP AT PRESSURE PIPE UP TO ENGINE 4507500
HEX. NUT
M 5 DIN 934-5 S FOR PIPE CLAMP AT PRESSURE PIPE FROM ENGINE 4507501-6501468
HEX. NUT
M 5 DIN 934-5 S FOR PIPE CLAMP AT PRESSURE PIPE FROM ENGINE 6501469
A 6360780085 PIPE BRACKET
FOR FUEL PIPE, CYLINDERS 1 AND 2, AT WATER PUMP
108 A 6360780385 PIPE BRACKET
FOR FUEL PIPE, CYLINDERS 1 AND 2, AT WATER PUMP
109 A 6360780335 PIPE CLAMP
FOR PRESSURE PIPE 1 AND 2 AND VACUUM LINE AT WATER PUMP
HEX. -HD.SCREW
M 5X12 DIN 933-8 G FOR PIPE CLAMP AT PIPE BRACKET AND WATER PUMP
LOCK WASHER
B 5 DIN 127 FOR PIPE CLAMP AT PIPE BRACKET AND WATER PUMP
HEX. NUT
M 5 DIN 934-5 S FOR PIPE CLAMP AT PIPE BRACKET AND WATER PUMP
A 6360780185 PIPE BRACKET
FOR FUEL PIPE, CYLINDER 1, 3 AND 4, AT EXHAUST MANIFOLD
113 A 6360780285 PIPE BRACKET
FOR FUEL PIPE, CYLINDER 1, 3 AND 4, AT EXHAUST MANIFOLD UP TO ENGINE 6501468
113 A 6360780285 PIPE BRACKET
FOR FUEL PIPE, CYLINDER 1, 3 AND 4, AT EXHAUST MANIFOLD FROM ENGINE 6501469
114 A 6360780086 RUBBER PAD
FOR PRESSURE LINE, CYLINDERS 3 AND 4 FROM ENGINE 6501469
A 6360701035 PART NAME MISSING
A 6360701135 LEAK LINE
115 A 6360701235 LEAK LINE
A 6360700040 BRACKET, T-FITTING
AT TIMING GEAR CASE COVER
A 6360700140 BRACKET, T-FITTING
AT TIMING GEAR CASE COVER UP TO ENGINE 7507990
116 A 6360700240 BRACKET, T-FITTING
AT TIMING GEAR CASE COVER FROM ENGINE 7507991
Reklama
Kontaktai
Pasiūlymas
Skaitliukas
 


© 2010-2013 UAB "RPV" Paslaugų teikimo sąlygos - Privatumo politika - Kopijuoti ir naudoti komerciniais tikslais draudžiama